Week 6 - Actual circuit construction (Metal and Ultrasonic sensor)

As the main circuit is already constructed and waiting to be installed, I continue to construct the other 2 sensor which is the ultrasonic and metal sensor, this metal sensor is different from the original planned, but the shop mention that the function is the same as the previous sensor and it has longer life span.

While doing and studying the circuit function and all, I am searching for any wood shop around PJ area to fabricate my project body. It is to make sure that the price is affordable and as budget. The body dimension should be 40W x 36D x 42H in cm.

NOTE: This is an early stages of circuit construction and not fully measure to the project body or mainframe.

Week 5 - Workshop on Chapter 4, 5 and Abstract in Thesis Writing

This workshop is conducted at TTL2 by Dr. Imran, basically he explain about result and discussion to be put and analyse in the report writing. Below are the slide during the session.

Week 4 - Actual Circuit Construction (Arduino, Servo Motor and Voltage Regulator)

During this week, the actual circuit is constructed and the focus was to connect the LM 7596, Arduino UNO and the servo motor. Below are the picture of servo wire construction on going but not yet install at the project body as it is not begin yet;

Note that the circuit is not running yet due to incomplete circuit construction as it will be done when the project body is fabricated. This is an early stages of circuit construction and not fully measure to the project body or mainframe.

Week 3 - Circuit construction finalize in Proteus

During this week, the circuit from FYP1 will be used and it is finalize, but it is not functioning even after converting the coding into HEX file, it shows error as the functioning wifi is not in the software so it cannot function unless working wifi is available in PROTEUS. So the project will be constructed without simulation.

Below is the recap on the circuit

At the same time, some of the part is bougt, which is the

• Arduino UNO
• Servo Motor
• Wifi Module
• Ultrasonic sensor

The metal sensor is not bought yet as the one to be use is out of stock, as this project is not using IR sensor as mention in FYP1. Below are metal sensor thought to be use but out of stock :

Week 2 - FYP2 Introductory Briefing

Title : First FYP Briefing

Activity :

On 31/7/2019(Wednesday), FYP2 introductory briefing was conducted. The briefing was conducted in TTL G04 and the attendance is compulsory.

The briefing was conducted by Sir Imran and announce that he is the updated FYP advisor.

Objective and content of briefing :

• To explain about FYP2 calendar
• To inform student to update their project frequently
• To update the FYP2 Title changing (if needed)

• To explain about Project Assessment
• To announce the Presentation day
• To inform the Submission date of project

Handout and Photos:

Week 1 - FYP2 Recap, Downloading and Installing Software

A quick recap on this Sorting and Monitoring of Recycle Item, basically this project will maintain the same title as before as it is more clear to use the function of the project as a title. The main function is still to detect and sort the general waste and aluminium or metal waste, Moreover it will be having a monitoring function to monitor the trash level. As decided the body of the project will be using a wood as this is just a prototype. It will also maintain all the function, software, hardware use as previous presented on FYP 1

As a start, I downloaded and updated all the software needed for this project because some of the software installed in my laptop is not in use for some time and cannot be use anymore. This week is also use to recap and get familiarize back with the software in order to develop the project. Below are the example of sofwares to be used. Below are the software downloaded and used;

1) Proteus

I used proteus for the circuit design and to simulate the circuit and check whether there is an error or not. Moreover, it is compatible with arduino software that I am using. As u can see from previous picture, my circuit is constructed using this software. 

2) Arduino

I use this software to write the program of the project .Furthermore i use this Arduino also simplifies the process of working with microcontrollers, but it offers some advantage for teachers, students, and interested amateurs over other systems:

1. Inexpensive - Arduino boards are relatively inexpensive compared to other microcontroller platforms. The least expensive version of the Arduino module can be assembled by hand, and even the pre-assembled Arduino modules cost less than $50

2. Cross-platform - The Arduino software runs on Windows, Macintosh OSX, and Linux operating systems. Most microcontroller systems are limited to Windows.

3. Simple, clear programming environment - The Arduino programming environment is easy-to-use for beginners, yet flexible enough for advanced users to take advantage of as well. For teachers, it's conveniently based on the Processing programming environment, so students learning to program in that environment will be familiar with the look and feel of Arduino

4. Open source and extensible software- The Arduino software is published as open source tools, available for extension by experienced programmers. The language can be expanded through C++ libraries, and people wanting to understand the technical details can make the leap from Arduino to the AVR C programming language on which it's based. Similarly, you can add AVR-C code directly into your Arduino programs if you want to.

5. Open source and extensible hardware - The Arduino is based on Atmel's ATMEGA8 and ATMEGA168 microcontrollers. The plans for the modules are published under a Creative Commons license, so experienced circuit designers can make their own version of the module, extending it and improving it. Even relatively inexperienced users can build the breadboard version of the module in order to understand how it works and save money.

Week 15 - 17 Report Submission and Blog Updated

During this whole week the focus stay on drafting the report for proposal and submitted to supervisor for the plagiarism check, below are the attempt of the plagiarism check

Chapter 1 First Plagiarism Check
Chapter 2 First Plagiarism Check
Chapter 3 First Plagiarism Check

and after the result of plagiarism check is not convincing Supervisor ask to repair and submit a full  compiled report for next plagiarism check.

Full Report PlagiarimCheck Result

With the result of 4% the hardcover is submit later on 12th JUNE 2019

The blog is also finished and updated during this 3 weeks period